Wall-Mounted Pull-Up Station SQMIZE® PU280-S with Cannonball Grips
Wall-Mounted Pull-Up Station SQMIZE® PU280-S with Cannonball Grips
€139.95
% €224.95* (37.79% saved)
Available, delivery time: 2-5 Tage
Wall-Mounted Pull-Up Station SQMIZE® PU280-S with Cannonball Grips
The SQMIZE® PU280-S Wall-Mounted Pull-Up Station offers seven grip positions in a single wall-mounted unit. Straight, angled, and neutral grips for pulling exercises, plus four welded-on Cannonball Grips in two sizes for grip strength training. At 111 cm wide, 54 cm deep, and just 16 cm high, the station has a low-profile design that sits close to the wall.
Seven Grip Positions Across 111 cm
Four tubes project vertically from the wall plate to form the neutral grips: 73 cm apart on the outside and 36 cm apart on the inside. The straight grips are positioned between the tubes, with a spacing of 36 cm. In the center, a V-shaped section brings the two angled grips together, spaced 22 cm apart. Two additional straight sections extend outward across the full width. All distances are measured center to center.
The straight and angled grips have a diameter of 32.5 mm. This substantial diameter fills the hand and engages the finger flexors from the very first repetition.
Cannonball Grips in 99 mm and 69 mm
The four balls are welded onto the ends of the tubes: two with a 99 mm diameter on the outside, spaced 74 cm apart, and two with a 69 mm diameter on the inside, spaced 36 cm apart. With a ball grip, you cannot fully wrap your hand around the handle. Instead, you pull using an open grip formed by your fingertips and the base of your thumb. This specifically trains the finger flexors, forearms, and wrist stability.
The 69 mm balls provide an entry point, while the 99 mm balls demand considerably more grip strength. You can progress gradually between the two sizes without having to attach any additional accessories.
Training with the PU280-S
Wide-grip pull-ups on the outer straight sections target the latissimus dorsi across a wide range of motion. Close-grip and neutral-grip positions place greater emphasis on the lower lats, biceps, and brachialis, while the angled grips keep your wrists and shoulders aligned throughout the movement. Hanging leg raises and toes-to-bar can be performed on any of the straight grip axes.
The Cannonball Grips add timed dead hangs, open-grip pull-ups, and one-arm hanging variations to your training. This makes the station suitable for both pulling volume and dedicated grip strength work.
Technical Specifications
| Overall Dimensions and Frame | |
|---|---|
| Overall dimensions (W × D × H) | 111 × 54 × 16 cm |
| Weight | 11 kg |
| Coating | Fine-textured powder coating |
| Load capacity (static) | Up to 350 kg, provided suitable wall anchors are used and properly installed |
| Grips | |
|---|---|
| Grip positions | 7 |
| Straight and angled grip diameter | 32.5 mm |
| Cannonball Grips | 99 mm and 69 mm, 2 of each, welded on |
| Inner straight grip spacing | 36 cm |
| Inner angled grip spacing | 22 cm |
| Outer neutral grip spacing | 73 cm |
| Inner neutral grip spacing | 36 cm |
| 99 mm Cannonball spacing | 74 cm |
| 69 mm Cannonball spacing | 36 cm |
| Scope of Delivery | |
|---|---|
| Scope of delivery | PU280-S Wall-Mounted Pull-Up Station, wall anchor set |
Mounting Instructions
The PU280-S is bolted to the wall using the full-length wall plate, which features a cutout SQMIZE logo. Choose anchors suitable for the mounting surface: for concrete and solid brick, you can use the included set; for porous or multi-layer masonry, special-purpose anchors provide the necessary additional load capacity.
At a Glance
- 7 grip positions: straight, angled, and neutral
- 4 welded-on Cannonball Grips in 99 mm and 69 mm sizes
- 32.5 mm grip diameter on the straight and angled grips
- 111 × 54 × 16 cm, low-profile wall-mounted design
- Static load capacity of up to 350 kg
Login